| DOTD TR 601 |
Qualification Procedure for Shear Connector Stud Weldability |
| |
The purpose of this procedure is to prescribe weldability test which will qualify a shear connector stud for welding under shop or field conditions
|
DOTD TR 602
|
Measuring Thickness and Widths of Base and Subbase Courses and Aggregate Type Surface Courses
|
| |
This method covers the procedure for determining the thickness and widths of base and subbase courses and of aggregate type surface courses for acceptance measurements and verification measurements of contractor's quality control
|
DOTD TR 603
|
Calibration and Certification of Rolling Straightedge
|
| |
This method describes a standard procedure for the calibration and certification of the ten-foot, four-wheel rolling straightedge
|
DOTD TR 610
|
Infrared Spectophotometric Analysis |
| |
This method determines the infrared spectra of materials when infrared light absorption wavelengths are within the range of 4000 to 650 cm-1
|
DOTD TR 612
|
Compression-Deflection of Preformed Compression Joint Seals
|
| |
This method of test describes the procedure for determining the sidewall pressure exerted by preformed elastomeric compression joint seals
|
DOTD TR 617
|
Measurement of Texture Depth by Sand-Patch
|
| |
This method describes a procedure for determining the average texture depth of a selected portion of pavement surface
|
DOTD TR 618
|
Use of Rolling Straightedge
|
| |
This method describes the use of the rolling straightedge for determining pavement surface irregularities
|
DOTD TR 628
|
Field Unit Weights of Aggregates by Truck Measure |
| |
This method covers the procedure used to determine as hauled bulk unit weights, lb/yd3 (kg/m3), of aggregates in the field by truck measurements
|
DOTD TR 633
|
Flow of Grout Mixtures
Effective 3/29/19, This procedure is no longer used, refer to ASTM C939 - Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone)
|
| |
This method of test covers the procedure to be used for determining the flow of grout mixtures by measuring the time of efflux of a specified volumen of grout through a standard flow cone |
DOTD TR 634
|
Sieve Analysis of Glass Beads |
| |
This method of test covers the procedure used to determine the gradation of glass beads used with traffice paint or thermoplastic striping material |
DOTD TR 636
|
Bonding Properties of Joint Former/Sealer |
| |
This method of test covers the procedure for
determining the bond strength between mortar and the plastic frame of
the joint former/sealer |
DOTD TR 639
|
Specific Intensity of Raised Pavement Markers
|
This method of test describes the procedure for determining the specific intensity of reflective raised pavement markers
|
|
Calibration of Measures Used to Determine Unit Weights
|
| |
This method covers the procedure for determining the calibrated volume of a unit weight measure
|
| DOTD TR 641 |
Determining Pavement Profile by Use of a California Type Profilograph
|
| |
This method describes procedures used to test pavement for surface smoothness with an approved California Type Profilograph
|
| DOTD TR 643 |
Determining Chloride Content in Admixtures for Portland Cement Concrete
|
| |
This method describes the determination of chloride content in admixtures for Portalnd cement concrete.
|
| DOTD TR 644 |
Determining the Longitudinal Profile Roughness of Traveled Surfaces Using Automated Profilers
|
| |
This method describes the procedure to be used for measuring and reporting longitudinal profile roughness of traveled surfaces using an inertial profiler
|
| DOTD TR 645 |
The Determination of In-Place Stiffness by the Dynamic Cone Penetrometer (DCP)
|
| |
The DCP can be used to measure the stiffness of cohesive and non-cohesive soils, base course aggregates, recycled asphalt pavement, recycled concrete pavement, blended calcium sulfate and in some instances chemically (cement or lime) stabilized or treated soils. |